How-to

RAM Mounts ball sizes B, C, D and E: heavy-duty vehicle mounting

Choose the right RAM ball size, arm length and base for rugged tablets, laptops and displays in off-road and service vehicles, with RAM's load table and part-number letters.

15 min Difficulty: Medium Updated: By SCANSHOP team
In this guide

    Every RAM mount is a chain of three parts: a ball base on the vehicle, a double socket arm and a ball on the device holder. The RAM ball size (B, C, D or E) sets how much weight that chain carries, so get it right first for a rugged tablet, laptop or display in an off-road or service vehicle. For docks, power and locking, see our RAM Mounts guide for defence and security vehicles.

    You'll need
    • A scale: weigh the device with its case, holder or dock and cables, then compare with RAM's table
    • The rail diameter, post width or flat area where the mount goes
    • The vehicle maker's instructions for that area

    RAM Mounts logo

    Choose the RAM ball size by weight

    Size Ball diameter Approx. max load* RAM's typical use
    A 14.3 mm (0.56") 0.5 lb (≈0.23 kg) Ultra-light devices
    B 25.4 mm (1") 2 lb (≈0.9 kg) Phones, GPS units, small tablets
    C 38.1 mm (1.5") 4 lb (≈1.8 kg) Large tablets, rougher rides
    D 57.2 mm (2.25") 6 lb (≈2.7 kg) Rugged tablets, laptops, heavy equipment
    E 85.9 mm (3.38") 15 lb (≈6.8 kg) Large displays, demanding industrial use

    * RAM: "Approximate capacity for a standard ball with a mid-length arm." Shorter arms and steel-reinforced posts increase real-world capacity (RAM). The kg values are our conversions.

    RAM lists lower loads for heavy-duty use, so leave a margin for rough roads. If the device is too heavy for a size, RAM recommends the next size up. For rugged tablets, RAM's knowledge base says: "For most mobile terminals and rugged tablets that require modular mounting, the D-Size ball is sufficient."

    123456
    RAM ball sizes to scale. 1 A · 2 B · 3 C · 4 D, the usual size for rugged tablets · 5 E · 6 Scale: 50 mm

    Video: RAM Mounts

    Pick the shortest arm that reaches

    RAM UK says the rubber ball greatly reduces the vibration that reaches your electronics; it doesn't remove it.

    712345689
    1 Ball base · 2 Rubber ball · 3 Double socket arm · 4 Knob · 5 Ball plate on the holder · 6 Device · 7 Small swing with a short arm · 8 Larger swing with a long arm · 9 Vehicle vibration
    Size Short Medium Long
    B 61 mm
    RAM-B-201U-A
    95 mm
    RAM-B-201U
    152 mm
    RAM-B-201U-C
    C 90 mm
    RAM-201U-B
    145 mm
    RAM-201U
    232 mm
    RAM-201U-D
    D 130 mm
    RAM-D-201U-C
    214 mm
    RAM-D-201U
    330 mm
    RAM-D-201U-E
    E 186 mm
    RAM-E-201U-D
    321 mm
    RAM-E-201U
    –

    Overall arm lengths, converted from RAM's inch figures. As RAM's footnote says, shorter arms increase real-world capacity. A longer arm is a longer lever: weight and bumps twist the ball joints harder, and the device swings further. Use the shortest arm that gives the reach you need.

    SCANSHOP is an official RAM Mounts reseller.

    Recommended D-size RAM arms, ball plate and wrench

    RAM Mounts D-size short double socket arm (130 mm) RAM-D-201U-C – product photo
    RAM MOUNTRAM Mounts Double Socket Arm, D-Size, Short ArmPart no. RAM-D-201U-C
    80,09 €+VATIn stock
    RAM Mounts D-size medium double socket arm (214 mm) RAM-D-201U – product photo
    RAM MOUNTRAM Mounts Double Socket Arm, D-Size, Medium ArmPart no. RAM-D-201U
    124,64 €+VATAvailable on request
    RAM Mounts D-size round AMPS ball plate – product photo
    RAM MOUNTRAM Mounts Round AMPS Plate with Ball, D-SizePart no. RAM-D-254U
    40,76 €+VATIn stock
    RAM Mounts Hi-Torq wrench for D-size socket arms – product photo
    RAM MOUNTRAM Mounts Hi-Torq Wrench for D-Size Socket ArmsPart no. RAM-KNOB9HU
    40,76 €+VATIn stock

    Buying for a fleet or a tender? Ask us for a quote.

    Get a quote

    How to read RAM part numbers

    RAM's naming guide puts the ball size after "RAM-": RAM-B- is B size, RAM- with no letter is C size, RAM-D- is D size and RAM-E- is E size. In RAM's examples the rest stays the same across sizes: 201U is the double socket arm, 202U the round plate. RAM doesn't explain the letter endings, which differ by size: compare the short arms above. For RAP- numbers, such as the C-size RAP-404U Tough-Claw, check the size in the product title.

    Mixing ball sizes: change the ball, not the arm

    An arm grips balls of its own size only; RAM says a D ball "is compatible with any other RAM® D Size ball & socket components". To combine sizes, change the ball:

    • Holders and docks with the 4-hole AMPS pattern (≈30 × 38 mm): fit a B (RAM-B-347U), C (RAM-347U) or D (RAM-D-254U) ball plate. The GDS Tough-Dock for the Galaxy Tab Active5 uses this pattern.
    • A second, light device on a C arm: the RAM-B-273-CU Add-A-Ball replaces the arm's bolt with a B ball; short and medium C arms only.

    Choose the base for the mounting surface

    Tough-Claw clamps need no tools but take only a B or C ball; for D-size loads use a metal D base.

    Surface Base Fit (RAM)
    Flat panel or floor RAM-D-202U round plate ≈93 mm (3.68") drill-down plate
    AMPS holder or flat surface RAM-D-254U round AMPS plate ≈64 mm (2.5"), 4-hole AMPS
    VESA display or dock RAM-D-246U-IN1 steel-reinforced plate 100 × 100 and 75 × 75 mm holes
    Rails and roll bars, no tools Tough-Claw small, medium (RAP-404U) or large Round ≈16–38, 25–48 or 25–57 mm; flat up to ≈29, 41 or 56 mm
    Rails, D size RAM-D-235U U-bolt base or RAM-D-271U-12 rail clamp ≈25–32 mm (1"–1.25") or ≈32–48 mm (1.25"–1.875")
    Square posts RAM-D-247U-4 post clamp Up to ≈102 mm (4") wide; RAM: "ideal for forklift mounting"
    Lift-truck overhead guard RAM-335 guard base Steel plates with many hole patterns; up to two balls
    Important

    RAM: "Do not install this product near or over an airbag deployment area or in a location that obstructs the driver's vision or interferes with vehicle operation." Follow the vehicle maker's and RAM's instructions, check behind panels before drilling, and leave hardwired power to a qualified installer.

    Recommended RAM bases for posts and rails

    Buying for a fleet or a tender? Ask us for a quote.

    Get a quote

    Tighten D-size arms with the Hi-Torq wrench

    The Hi-Torq wrench fits the knob of D-size arms for an extra tight grip. RAM says it was originally made for the military, for cold weather when the knob could not be tightened by hand. Tighten by hand first; use the wrench only if a correctly sized set-up still moves when pushed firmly, and recheck after the first rough drives. To stop others removing the mount, RAM's Pin-Lock nut replaces the knob on D and E arms; see locking RAM mounts against theft.

    Common mistakes

    • An under-sized ball. Choose by total weight, not screen size.
    • A long arm on a heavy device. It shakes on the road; move the base closer instead.
    • Cranking the knob. If the device only holds with the knob as tight as you can get it, the ball is too small or the arm too long. No pliers or bars on knobs.
    • Airbag zone or driver's view. Plan the position before you drill.

    Frequently asked questions

    What size RAM ball do I need for a 10-inch rugged tablet?

    Weigh it with its case and holder or dock. RAM says D size is sufficient for most rugged tablets, and with a short arm it gives the most margin on rough roads. See our rugged tablet vehicle mount guide.

    What is the difference between RAM B and C size?

    The B ball is 25.4 mm (1") and the C ball 38.1 mm (1.5"). RAM's approximate maximum loads are 2 lb (≈0.9 kg) and 4 lb (≈1.8 kg), for a standard ball with a mid-length arm.

    Are RAM B, C and D parts interchangeable?

    No, an arm grips balls of its own size only. Combine sizes by changing the ball plate on the holder, for example to a D-size AMPS ball plate.

    Do I need the Hi-Torq wrench?

    Only if you can't tighten a D-size knob enough by hand, for example in cold weather.

    Was this guide helpful?

    Used in this guide

    Compatible consumables and accessories for the RAM Mounts Double Socket Arm, D-Size, Medium Arm (RAM-D-201U).

    Products used in this guide

    ProductPrice
    RAM Mounts Double Socket Arm, D-Size, Short Arm (RAM-D-201U-C) RAM Mounts Double Socket Arm, D-Size, Short ArmRAM-D-201U-C80,09 €+VATIn stock
    RAM Mounts Double Socket Arm, D-Size, Medium Arm (RAM-D-201U) RAM Mounts Double Socket Arm, D-Size, Medium ArmRAM-D-201U124,64 €+VATOut of stock View
    RAM Mounts Round AMPS Plate with Ball, D-Size (RAM-D-254U) RAM Mounts Round AMPS Plate with Ball, D-SizeRAM-D-254U40,76 €+VATIn stock
    RAM Mounts Hi-Torq Wrench for D-Size Socket Arms (RAM-KNOB9HU) RAM Mounts Hi-Torq Wrench for D-Size Socket ArmsRAM-KNOB9HU40,76 €+VATIn stock
    RAM Mounts Square Post Clamp Base for Posts up to 102 mm (4") Wide, D-Size (RAM-D-247U-4) RAM Mounts Square Post Clamp Base for Posts up to 102 mm (4") Wide, D-SizeRAM-D-247U-482,70 €+VATIn stock
    RAM Mounts Tough-Claw Medium Clamp Ball Base for 25.4–40.6 mm Bars, C-Size (RAP-404U) RAM Mounts Tough-Claw Medium Clamp Ball Base for 25.4–40.6 mm Bars, C-SizeRAP-404U68,48 €+VATIn stock

    Related guides

    Still stuck?

    Send us your model and a short description of the problem. Our team will help you find a solution.

    Contact support
    RAM Mounts Double Socket Arm, D-Size, Medium Arm (RAM-D-201U)124,64 €+VAT View product